+ 61 2 9533 7877

Archives

CC610PB Solution 6000 Control Panelfsdfds

Product Details

16 on-board zones (expandable to 144 wired or wireless), partitionable to 8 areas with 256 PIN, token, keyfob and fingerprint users
Integrated access control for up to 16 doors
Proximity key pads, Weather-proof external metal keypads, Internal & External LAN readers & Fingerprint LAN readers available
5 on-board outputs (expandable to 37)
GSM/GPRS and Ethernet options

POWER REQUIREMENTS
Voltage Input	16-18V A.C 50-60Hz – 24VA External Power Adaptor or 220-240V A.C. to 18V A.C 50-60Hz – 24VA Internal Transformer (Primary Power Source)
Continuous Power	1 Amp MAX (Combined power drawn from Accessory Power (+12V) LAN Power (Module LAN+) and Output Power (C+) terminals must not exceed 1 Amp.
Alarm Power	4 Amp (Total with primary and secondary power sources fitted)
Stand-by Battery	12 VDC, 7.2AH sealed rechargeable battery – Panasonic LC-P127R2P or equivalent. (Secondary Power Source). Dispose of used batteries according to instructions.
Min Operating Voltage	10.2 VDC
Battery Charger	Pulse by pulse charger. (Note: Charge voltage cannot be measured unless battery is fitted.)
Connections
Module Connection (RS485 LAN)	Max. total LAN length using multi strand security cable = 300mMax. total LAN length using 2 pair twisted shielded data cable (Belden 8723) = 1200m.See the product installation manual for complete wiring instructions.
Telephone Connections	RJ-12 Socket or 4-way terminal
Communications
Communications	CID, SIA, SMS, Email, Voice, Domestic Dialling, GSM-CID, GSM-SMS, Connetix IP, CSV-IP
Environmental Considerations
Temperature	0o to 55oC
Relative Humidity	5 to 85% non-condensing

ENCLOSURE
Enclosure Fixing Method	CM720B – Small EnclosureUsing appropriate fasteners capable of handling a minimum of 6kgs to fix the cabinet against a sturdy surface using the mounting holes provided.CM730B – Large EnclosureUsing appropriate fasteners capable of handling a minimum of 12kgs to fix the cabinet against a sturdy surface using the mounting holes provided.
Enclosure Dimensions	MW720B: 385(W), 260(H), 90(D)mmMW730B: 385(W), 520(H), 90(D)mm
PWA Dimensions	235(W), 85(H), 40(D)mm
Warranty	3 years

Document Download Link:

Installation Manual

Installation Note

Quick Installation Guide

Operation Manual

CM101B Voice Message Modulefsdfds

Turn your system ON / OFF using your mobile phone – secure connection requires valid PIN
Operate outputs remotely with voice prompts
Zone and area names can be customised
Eliminates domestic reporting ambiguity – receive alarm information by voice on any phone
Use as a primary and / or secondary reporting path

Power Requirements
Operating Voltage:	Supplied by panel – derate the maximum available 12V accessory power from the panel by 20mA when the module is fitted
Reporting & Connections
Report Options:	Voice messages on Primary or Secondary Report route
Fixing Method:	The CM101B mounts directly onto the control panel via the 8 way pin header and is supported at the opposite end using the supplied plastic stand-off
Environmental Considerations
Temperature:	0o to 55oC relative
Humidity:	5% to 85% at 30oC non-condensing
PCB
Dimensions:	50(W) x 23(D) x 58(H)mm
Warranty:	3 years

Document Download Link:

Data Sheet

Operation Manual (CM101B)

CM195 Multi Receiver Interfacefsdfds

Product Details

Provides increased wireless coverage
Multi vendor wireless capable
Module Status and Receiver status LEDs
Separate tamper input


Voltage	10.5 to 14 V D C
Current	100 m A MAX
Cable	3 wire connection to control panel INPUT terminal

Temperature	0 to 55 ° C
Humidity	5 % to 85 % at 30 ° C non condensing

Document Download Link:

CM704B 8/16 ZONE INPUT EXPANDER MOD PCB (RS485)fsdfds

Product Details

High security module with anti-substitution protection and resettable fuse protection on power out terminals
Supports Single, Alarm+Tamper and Split EOL, with up to 15 different EOL Resistor options
6 Power Out terminals simplify wiring; outputs are overload and short circuit proof
Service Code Pad connection point
LAN Termination Shunt and status indicators included

Power Requirements
Operating Voltage:	10.0V DC – 14.5V Dc @ 90mA Max
Voltage Input (Primary Source):	16-18V AC 50-60Hz – 24VA External Power Adaptor or 220-240V AC to 18V AC 50-60Hz – 24VA Internal Transformer
Stand-By – Battery (Secondary Source):	12V DC, 7.2AH sealed rechargeable battery Panasonic LC-P127R2P or equivalent
Connections
Module Connection (RS485 LAN):	Max total LAN length using multi strand security cable = 300m;Max total LAN length using 2 pair twisted shielded data cable (Belden 8723) = 1200m.See manual for complete wiring instructions.
Programmable Outputs:	4 protected open-collector outputs capable of providing a maximum of 500mA (-) each. Outputs are monitored for short and open circuit and can monitor the state of horn speakers and other connected devices.
Power Output Terminals:	COMM+ – 2.5A high current output for use with onboard outputs, PTC fuse protected. +12V -1A outputs for use with detectors or powering other modules, PTC fuse protected.
Environmental Considerations
Temperature:	-30o to 55oC Operating
Humidity:	5% to 85% at 30oC non-condensing
PCB
Fixing Method:	The CM705B can be mounted in the MW700, MW710, Mw720 or MW730 enclosures using clip-in PCB mounts supplied
PWA Dimensions:	235(W) x 85(D) x 40(H)mm
Warranty:	3 years

Document Download Link:

Installation Manual (C705PB-CM707B)

CM710B OUTPUT MODULE 4-WAY RELAY (RS485)fsdfds

4 x Form C relay contacts
LAN monitored
Status LED
Service code pad connection
Separate tamper input
Automatic recognition by panel

Voltage	10.5 to 14 V D C
Current	30m A standby, 200m A MAX (all relays and LEDs operated)
Outputs	4 x Form C Relay outputs – contacts rated at 24VD C at 2A MAX
Cable	Max total LAN length using multi stranded security cable = 300m Max total LAN length using 2 pair twisted shielded data cable (Belden 8723) = 1500m

Temperature	0 to 55 ° C
Humidity	5 % to 85 % at 30 ° C non condensing

Document Download Link:

CM720B 1-Amp LAN Power Supplyfsdfds

Product Details

1 Amp continuous rated; LAN monitored
Multiple protected power outputs
Resettable fuse protected
Pulse battery charger
AC Fail output, low battery output and low battery indicator

Power Requirements
Voltage Input (Primary Source:)	16-18V AC 50-60Hz – 24VA External Power Adaptor or 220-240V AC to 18V AC 50-60Hz – 24VA Internal Transformer
Stand-By Battery (Secondary Source):	12V DC, 7.2AH sealed rechargeable battery Panasonic LC-P12R2P or equivalent. Resettable Fuse Protected @ 3 Amps
Voltage Output:	13.8V DC @ 1 Amp. Ripple 100mV @ Full Load (Primary supply source only)
Battery Monitoring:	11.5V DC Low battery trouble at keypads, low battery report sent (if programmed) 10.0V DC Shut down as voltage fails below 9V DC13.0V DC Battery trouble clears from keypads, battery restore report sent (if programmed)
Connections
Module Connection (RS485 LAN):	Max total LAN length using multi strand security cable = 300mMax total LAN length using 2 pair twisted shielded data cable (Belden 8723) = 1200m
Outputs:	3 Output Terminals providing a total of 1 Amp output current (Resettable Fuse Protected) AC Fail – 50mA Max – Sink – 120mA – Overload Protected Low Battery – 50mA Max – Sink – 120mA – Overload Protected
Inputs:	Cabinet Tamper
Environmental Considerations
Temperature:	0o to 55oC Operating
Humidity:	5% to 85% at 30oC non-condensing
Enclosure
Dimensions:	115(W) x 86(D) x 30(H)mm
Warranty:	3 years

CM723B 5 Amp LAN Power Supply Modulefsdfds

Product Details

5 Amps total combined output current
Charge up to 2 x 7.2Ah or 1 x 18Ah standby batteries
Remotely interrogate power supply status via RAS
Resettable fuse protected with deep discharge protection built-in
Easily installed into MW720 or MW730 enclosures

Power Requirements
Voltage Input:	100-240V AC @ 2.0A 50-60Hz
Stand-by Battery:	Up to 2 x 12V DC 7.2Ah sealed rechargeable battery Panasonic LC-P12R2P or equivalent or 1 x 12V DC 18Ah sealed rechargeable batteryResettable fuse protected @ 6 Amps
Voltage Output:	13.8V DC @ 5 Amps (Primary supply source only)
Battery Discharge Cycle:	AC Off: Keypads indicate trouble condition, AV Fail report resent (if programmed)13.8V DC :Charging level11.5V DC: Low battery trouble at keypads, low battery report sent (if programmed)10.0V: DC Shut down and battery disconnected as voltage falls below 9V DC.
Battery Recharge Cycle:	AC On: Panel restarts, battery charging begins. AC trouble clears from keypads, AC restore report sent (if programmed).12.8V DC: Battery trouble clears from keypads, battery restore report sent (if programmed).13.8V DC: Battery float charged.
Connections
Connection (RS485 LAN):	Max total LAN length using multi strand security cable = 300mMax total LAN length using 2 pair twisted shielded data cable (Belden 8723) = 1200m
Environmental Considerations
Temperature:	0o to 55oC Operating
Humidity:	5% to 85% at 30oC non condensing
Enclosure
Dimensions:	50(W) x 23(D) x 58(H)mm
Warranty:	3 years

CM751B Solution Conettix IP Ethernet Modulefsdfds

Product Details

High security (128bit encryption) replacement for PSTN line
Remote upload / download over IP and alarm reporting over LAN/WAN
Operate outputs and areas remotely
Dynamic and fixed IP address support
Conettix and CSV-IP reporting formats

Power Requirements
Operating Voltage:	Supplied by panel – derate the maximum available 12V accessory power from the panel by 60mA when the module is fitted
Connections
Network Interface:	RJ45 Ethernet 10base-t or 100base-TX (Auto Sensing)
Protocols Supported:	RP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, Auto IP, SMTP, and httpSolutionLink Upload / Download Software, Conettix, CSV IP, MyAlarm CID etc
Encryption:	128 bit AES Rijndael
Module Connection:	The CM751B mounts to the control panel PWA via the expansion port header and 3 plastic PCB standoffs provided. The HW750 Riser Kit, also included, should be used when the CM751B and CM101B Voice Module are installed on the same panel.
Environmental Considerations
Temperature:	0o to 55oC Operating
Humidity:	5% to 85% at 30oC non-condensing
Enclosure
Dimensions:	93(W) x 52(D) x 30(H)mm
Warranty:	3 years

CM760B Real Time Clock Modulefsdfds

Product Details

Accuracy better than =/- 2 minutes / calendar year
Simple RS485 LAN connection to control panel
Local low battery fault indicator and dedicated tamper input
LAN monitored, encrypted data and anti-substitution
Service keypad connection point included

Power Requirements
Operating Voltage:	10.5V DC – 14.0V DC @ 50mA Stand-by
Battery Type:	3V Lithilum button cell type (CR2032 size)
Battery Life:	Approx. 3 years
Connections
Module Connection (RS485 LAN):	Max total LAN length using multi-strand security cable = 300mMax total LAN Length using 2 pair twisted shielded data cable (Belden 8723) – 1200mSee manual for complete wiring instructions.
Inputs	Cabinet tamper
Fixing Method:	The CM760 can be mounted in the MW700, Mw710, MW720 or MW730 enclosures using clip in PCB mounts supplied
Accuracy:	Better than +/- 2 minutes per calendar year
Environmental Considerations:
Temperature:	0o to 55oC Relative humidity 5% to 85% at 30oC non-condensing
Dimensions:	115(W) x 86(D) x 30H)mm
Warranty:	3 years

CP700B KEYPAD GRAPHIC WHITECASE/BLUE (RS485)fsdfds

Product Details

Large graphical display with LED backlight, with real time clock and temperature display
Up to 4 lines of 20 characters and icons, with dedicated On, OFF and PART keys
Alphanumeric text prompting / programming with custom installer static display screen
Adjustable volume, backlight and contrast
Terminal block connections

Power Requirements
Current:	30mA Standby (Backlight off)740mA Max (Backlight on)
Enclosure
Dimensions:	90(W) x 23(D) x 146(H)mm
Environmental Considerations
Temperature:	0o to 85oC Operating
Humidity:	5% to 85% at 30oC non-condensing
Warranty:	3 years

Document Download Link:

CP710B Solution 6000 Graphic Keypad – Blackfsdfds

Product Details

Large graphical display with LED backlight, with real time clock and temperature display
Up to 4 lines of 20 characters and icons, with dedicated On, OFF and PART keys
Alphanumeric text prompting / programming with custom installer static display screen
Adjustable volume, backlight and contrast
Terminal block connections

Power Requirements
Current:	30mA Standby (Backlight off)740mA Max (Backlight on)
Enclosure
Dimensions:	90(W) x 23(D) x 146(H)mm
Environmental Considerations
Temperature:	0o to 85oC Operating
Humidity:	5% to 85% at 30oC non-condensing
Warranty:	3 years

Document Download Link:

ICP-SOL3-P Control panel, 16-zonefsdfds

Product Details

8/16 Fully Programmable Zones
41 Codes – 1 Installers, 20 User Codes, 20 RF Keyfobs
16 Wireless Devices (on Solution 3000)
Partitionable into 2 Separate Areas
STAY / AWAY Arming Options

Power Requirements
Primary	250 VAC / 18 VAC at 1.3A supplied by TF008 Plug Pack
Secondary	12 VDC, 6.5Ah from rechargeable sealed lead/acid battery
Communications
Communications	CID, SIA, Email, Domestic Dialing, CSV-IPRequires B426 IP Communications Module or B450 Universal Communications Module
Environmental Considerations
Temperature	0o to +45oC
Relative Humidity	10% to 95% non-condensing
Enclosure
Dimensions (H x W x D)(packed in carton)	306 x 262 x 84mm
Weight	2.5kg
Warranty	3 years

Document Download Link:

Quick Installation Guide (ICP-SOL2-SOL3)
Operation Manual (ICP_SOL2-SOL3)
Quick Selection Guide (Solution 2000/3000 Product Matrix)

Become a Trade customer