+ 61 2 9533 7877

Archives

CM101B Voice Message Modulefsdfds

More info

Turn your system ON / OFF using your mobile phone – secure connection requires valid PIN
Operate outputs remotely with voice prompts
Zone and area names can be customised
Eliminates domestic reporting ambiguity – receive alarm information by voice on any phone
Use as a primary and / or secondary reporting path

Power Requirements
Operating Voltage:	Supplied by panel – derate the maximum available 12V accessory power from the panel by 20mA when the module is fitted
Reporting & Connections
Report Options:	Voice messages on Primary or Secondary Report route
Fixing Method:	The CM101B mounts directly onto the control panel via the 8 way pin header and is supported at the opposite end using the supplied plastic stand-off
Environmental Considerations
Temperature:	0o to 55oC relative
Humidity:	5% to 85% at 30oC non-condensing
PCB
Dimensions:	50(W) x 23(D) x 58(H)mm
Warranty:	3 years

Document Download Link:

Data Sheet

Operation Manual (CM101B)

CM195 Multi Receiver Interfacefsdfds

More info

Product Details

Provides increased wireless coverage
Multi vendor wireless capable
Module Status and Receiver status LEDs
Separate tamper input


Voltage	10.5 to 14 V D C
Current	100 m A MAX
Cable	3 wire connection to control panel INPUT terminal

Temperature	0 to 55 ° C
Humidity	5 % to 85 % at 30 ° C non condensing

Document Download Link:

CM704B 8/16 ZONE INPUT EXPANDER MOD PCB (RS485)fsdfds

More info

Product Details

High security module with anti-substitution protection and resettable fuse protection on power out terminals
Supports Single, Alarm+Tamper and Split EOL, with up to 15 different EOL Resistor options
6 Power Out terminals simplify wiring; outputs are overload and short circuit proof
Service Code Pad connection point
LAN Termination Shunt and status indicators included

Power Requirements
Operating Voltage:	10.0V DC – 14.5V Dc @ 90mA Max
Voltage Input (Primary Source):	16-18V AC 50-60Hz – 24VA External Power Adaptor or 220-240V AC to 18V AC 50-60Hz – 24VA Internal Transformer
Stand-By – Battery (Secondary Source):	12V DC, 7.2AH sealed rechargeable battery Panasonic LC-P127R2P or equivalent
Connections
Module Connection (RS485 LAN):	Max total LAN length using multi strand security cable = 300m;Max total LAN length using 2 pair twisted shielded data cable (Belden 8723) = 1200m.See manual for complete wiring instructions.
Programmable Outputs:	4 protected open-collector outputs capable of providing a maximum of 500mA (-) each. Outputs are monitored for short and open circuit and can monitor the state of horn speakers and other connected devices.
Power Output Terminals:	COMM+ – 2.5A high current output for use with onboard outputs, PTC fuse protected. +12V -1A outputs for use with detectors or powering other modules, PTC fuse protected.
Environmental Considerations
Temperature:	-30o to 55oC Operating
Humidity:	5% to 85% at 30oC non-condensing
PCB
Fixing Method:	The CM705B can be mounted in the MW700, MW710, Mw720 or MW730 enclosures using clip-in PCB mounts supplied
PWA Dimensions:	235(W) x 85(D) x 40(H)mm
Warranty:	3 years

Document Download Link:

Installation Manual (C705PB-CM707B)

CM710B OUTPUT MODULE 4-WAY RELAY (RS485)fsdfds

More info

4 x Form C relay contacts
LAN monitored
Status LED
Service code pad connection
Separate tamper input
Automatic recognition by panel

Voltage	10.5 to 14 V D C
Current	30m A standby, 200m A MAX (all relays and LEDs operated)
Outputs	4 x Form C Relay outputs – contacts rated at 24VD C at 2A MAX
Cable	Max total LAN length using multi stranded security cable = 300m Max total LAN length using 2 pair twisted shielded data cable (Belden 8723) = 1500m

Temperature	0 to 55 ° C
Humidity	5 % to 85 % at 30 ° C non condensing

Document Download Link:

CM720B 1-Amp LAN Power Supplyfsdfds

More info

Product Details

1 Amp continuous rated; LAN monitored
Multiple protected power outputs
Resettable fuse protected
Pulse battery charger
AC Fail output, low battery output and low battery indicator

Power Requirements
Voltage Input (Primary Source:)	16-18V AC 50-60Hz – 24VA External Power Adaptor or 220-240V AC to 18V AC 50-60Hz – 24VA Internal Transformer
Stand-By Battery (Secondary Source):	12V DC, 7.2AH sealed rechargeable battery Panasonic LC-P12R2P or equivalent. Resettable Fuse Protected @ 3 Amps
Voltage Output:	13.8V DC @ 1 Amp. Ripple 100mV @ Full Load (Primary supply source only)
Battery Monitoring:	11.5V DC Low battery trouble at keypads, low battery report sent (if programmed) 10.0V DC Shut down as voltage fails below 9V DC13.0V DC Battery trouble clears from keypads, battery restore report sent (if programmed)
Connections
Module Connection (RS485 LAN):	Max total LAN length using multi strand security cable = 300mMax total LAN length using 2 pair twisted shielded data cable (Belden 8723) = 1200m
Outputs:	3 Output Terminals providing a total of 1 Amp output current (Resettable Fuse Protected) AC Fail – 50mA Max – Sink – 120mA – Overload Protected Low Battery – 50mA Max – Sink – 120mA – Overload Protected
Inputs:	Cabinet Tamper
Environmental Considerations
Temperature:	0o to 55oC Operating
Humidity:	5% to 85% at 30oC non-condensing
Enclosure
Dimensions:	115(W) x 86(D) x 30(H)mm
Warranty:	3 years

CM751B Solution Conettix IP Ethernet Modulefsdfds

More info

Product Details

High security (128bit encryption) replacement for PSTN line
Remote upload / download over IP and alarm reporting over LAN/WAN
Operate outputs and areas remotely
Dynamic and fixed IP address support
Conettix and CSV-IP reporting formats

Power Requirements
Operating Voltage:	Supplied by panel – derate the maximum available 12V accessory power from the panel by 60mA when the module is fitted
Connections
Network Interface:	RJ45 Ethernet 10base-t or 100base-TX (Auto Sensing)
Protocols Supported:	RP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, Auto IP, SMTP, and httpSolutionLink Upload / Download Software, Conettix, CSV IP, MyAlarm CID etc
Encryption:	128 bit AES Rijndael
Module Connection:	The CM751B mounts to the control panel PWA via the expansion port header and 3 plastic PCB standoffs provided. The HW750 Riser Kit, also included, should be used when the CM751B and CM101B Voice Module are installed on the same panel.
Environmental Considerations
Temperature:	0o to 55oC Operating
Humidity:	5% to 85% at 30oC non-condensing
Enclosure
Dimensions:	93(W) x 52(D) x 30(H)mm
Warranty:	3 years

CP710B Solution 6000 Graphic Keypad – Blackfsdfds

More info

Product Details

Large graphical display with LED backlight, with real time clock and temperature display
Up to 4 lines of 20 characters and icons, with dedicated On, OFF and PART keys
Alphanumeric text prompting / programming with custom installer static display screen
Adjustable volume, backlight and contrast
Terminal block connections

Power Requirements
Current:	30mA Standby (Backlight off)740mA Max (Backlight on)
Enclosure
Dimensions:	90(W) x 23(D) x 146(H)mm
Environmental Considerations
Temperature:	0o to 85oC Operating
Humidity:	5% to 85% at 30oC non-condensing
Warranty:	3 years

Document Download Link:

Fingerprint Readersfsdfds

More info

Product Details

Separate indicators show door and alarm status; built in sounder provides alarm warning
Lock output and egress input to simplify wiring, with built in tamper switch
Haptic feedback enhances user operation
Adjustable volume control
Anti replay and anti substitution protection

DOPower Requirements
Operating Voltage:	10.0V DC – 14.5V DC @ 100mA
Connections
Format:	Proprietary
Lock Output:	Protected open collector transistor output – 500mA
Egress Input:	Love (Ov) to trigger. Can be disabled via software control
Environmental Considerations
Temperature:	-30o to 55oC Operating
Humidity:	5% to 85% at 30oC non-condensing
Enclosure
Dimensions:	74(W) x 23(D) x 116(H)mm
Warranty:	3 years

Document Download Link:

Installation Manual (CM728B-CM729B)

Become a Trade customer